Caring for a HOPPE multipoint lock
How do you lubricate a multipoint lock? Clean it first, then go lightly.
With the door open, wash every locking point, let it dry, and put back a little of the same type of lubricant that was on it. A puff of dry graphite goes in the key slot. Once or twice a year is enough.
Which lubricant to use
Use what your lock's maker names. Lock makers don't agree, so there is no single right product for every multipoint lock.
HOPPE names no lubricant for this lock. Its catalog for the HLS One kit calls those parts self-lubricating, needing very little maintenance. So on a HOPPE lock, follow these rules:
- Same type as what's on it. Where there is grease, use grease.
- Graphite in the key slot only. A short puff of dry graphite.
- No silicone unless your lock's maker names it. Some makers warn it can make plastic parts brittle.
- Don't use WD-40 as the lubricant. It can free a stiff lock for a while, but oily sprays hold dust and the lock gets stiff again.
Another brand? Amesbury Truth names lithium grease for its gear-driven locks, and says greased gears get grease again, "not a spray such as WD40". Not sure who made your lock? Read the stamp on the metal strip in the door's edge, near the latch, or check whether it's a HOPPE HLS 9000.
Step by step
Open the door and prop it
Everything is done with the door open, so nothing presses on the bolts.
Wash the locking points
Wipe the latch, deadbolt, hooks or tongues, and any rods that shoot into the top of the frame and the sill. Use water and a little mild dish soap. Rinse, then let it dry completely. Don't use vinegar, citrus, chlorine, glass cleaner or anything abrasive: they strip the lubricant and the corrosion coating.
Vacuum the bolt holes
Clean out the holes in the top of the frame, the jamb and the sill. Grit in a hole drags on the bolt every time you lock.
Lubricate lightly
Put a little lubricant on each locking point where it slides out of the faceplate. A little is enough.
Work it in
Press in the small spring plunger beside the latch, lift the handle, then turn the key or thumbturn. Do it a few times. Turn the key back and push the handle down before you close the door.
Puff graphite in the key slot
Wipe the key first. Puff a little dry graphite in, then work the key in and out and turn it both ways. Never put oil or a wet spray on top of graphite: together they make a paste that jams the pins.
Wipe off the extra
Clean the faceplate and door edge. Grease and oil can stain wood and collect dust.
How often
Once or twice a year, and sooner if the key starts to drag. A good habit is to check exterior doors before summer and before winter.
| What to do | When |
|---|---|
| Clean and lubricate the locking points | Once or twice a year. Amesbury Truth says at least once a year, more often near the coast |
| Graphite in the key slot | Once or twice a year, or when the key drags |
| Snug the set screw under each lever (3 mm hex key on HOPPE) | When the lever starts to wobble. These screws work loose over time |
| Tighten the hinge and lock screws | At the twice-yearly check |
| Vacuum the bolt holes in the frame and sill | At the twice-yearly check |
Stiff only when the door is shut? That's not a lubricant problem. The door has moved in its frame and the bolts are rubbing their strike plates. No spray will cure it: adjust the door instead.
How long do multipoint locks last?
There is no fixed number of years. None of the makers' guides we checked gives one. How long a lock lasts depends mostly on how the door hangs and how the handle is treated.
HOPPE sells the HLS 9000 as all stainless steel and salt-spray tested for 3,000 hours. That is a test of rust resistance, not a promise of years. Door warranties don't settle it either: Therma-Tru, for one, excludes wear and tear on the multipoint system.
What wears a multipoint lock out
- Forcing the handle on a door that is out of line. One handle drives every bolt through a small set of gear teeth in the lock case. When the bolts press on their strikes, leaning on the handle is how those teeth break. One locksmith who repairs these locks says it is the lock case failure they see most.
- Locking a door that binds, day after day. A door out of line loads the bolts every time you lock it. That is the kind of load that wears a lock case out.
- Grit and the wrong lubricant. Dirt and oily sprays make the lock stiff, and a stiff lock gets forced.
- Lifting or pulling the door by its handle.
- Overtightened screws. The lock is fitted hand-tight. Too much force on its screws makes it bind.
Locksmiths who repair these locks report that the lock case is the part that wears out, and that the upper half rarely breaks. Because HOPPE sells this lock part by part, a worn case rarely means a whole new lock.
When care isn't enough
Smooth with the door open, stiff or hard to lock when shut.
The door has moved. The lock is working.
Fix the hinges and strikes before you buy anything.
The key is stiff, but the inside thumbturn is smooth.
The key or the key cylinder is worn, not the lock case.
Try a spare key. The cylinder comes out on its own.
Still stiff, crunchy or stopping partway with the door open, after cleaning. Or the handle droops.
Something inside the lock case has worn. Stop forcing it.
The door is locked shut and won't open.
Don't drill the lock, and don't spray it full of oil.
See door stuck shut, or call a locksmith. If anyone is locked in or in danger, call 911.
Questions about lock care
How do you lubricate a multipoint lock?
Open the door, wash each locking point with mild dish soap and water, and let it dry. Vacuum the bolt holes. Put a little of the same type of lubricant that was there on each point, as your lock's maker says, then work the handle and key a few times. A puff of dry graphite goes in the key slot.
How long do multipoint locks last?
There is no fixed number of years. What shortens a lock's life is a door out of line, a handle forced against bolts that are binding, and grit. A door that hangs right and a handle that isn't forced is the best care you can give it.
What lubricant does HOPPE recommend?
HOPPE names none for this lock. Use the same type that's already on it, graphite only in the key slot, no silicone, and not WD-40 as the lubricant.
Can I use WD-40 on a multipoint lock?
Not as the lubricant. It may free a stiff lock for a while, but oily sprays hold dust. Already used it? Wash the bolts with mild dish soap and water, dry them completely, and put the right lubricant back.
How often should I lubricate it?
Once or twice a year, and whenever the key starts to drag.
Will lubricant fix a handle that won't lift?
Not if it lifts easily with the door open. Then the door has moved in its frame, and the fix is adjusting the door. Forcing the handle is what breaks the lock case.
I cleaned and lubricated it and it's still stiff with the door open. Now what?
The lock case may be worn. Tell the problems apart, or send us a photo of the door's edge and tell us what it does. You can also use the instant part identifier. We reply by email within 1 business day.
The part
HOPPE HLS 9000 replacement lock case
- Genuine HOPPE part, in six sizes
- Choose your size for price and availability
- Free US shipping and 90-day free returns