HOPPE multipoint door handles
Drooping, loose, stiff or stuck? Find the part before you buy one.
Six handle problems look alike and need different fixes. Some need an adjustment rather than a replacement part. Here is how to tell them apart at the door.
What you see, and what it means
Open the door first. A lock behaves differently when nothing is pressing on its bolts, and that difference is half the answer.
The lever rests below level, or creeps back up slowly.
That is a drooping handle. The spring that returns the lever to level has worn out, or something is dragging on the handle.
Try the two free fixes below, then do the spindle check. If the test points to the lock case, this is the one-part fix.
The lever wobbles, but it still springs back to level.
That is a loose handle, not a drooping one. A loose set screw is one possible cause.
Look under the lever for a small screw. On HOPPE levers it takes a 3 mm hex key. Snug it and test again. If that fixes the wobble, no replacement part is needed.
The handle won't lift all the way with the door shut, but it locks easily with the door open.
Alignment or interference at the frame or strike plates may be loading the lock.
Look at the strike plates and hinges before you order a lock part. A new lock case will not fix a door that is out of line.
The key is hard to turn.
First lift the handle all the way up: on a lift-to-lock door the key will not turn until the handle is fully up.
Then try it with the door open. Easy when open and stiff when shut means the door is out of line. Stiff from the key side only points to the key cylinder, which comes out on its own. Stiff from both the key and the thumbturn, with the door open, points to the lock case.
With the door open, the handle clicks or flops, or the deadbolt will not come out.
A worn gear or spring inside the case is one possible cause; first rule out attachment and operating issues.
HOPPE doesn't sell those small parts, so the case is replaced as one unit. Check whether the case alone is enough.
The door is locked shut and will not open.
Don't drill the lock, and don't order a part yet.
Call a locksmith or a door installer. If anyone is locked in or in danger, call 911.
For a drooping handle
Two free fixes to try first
Snug the set screw
A badly loose lever can look like a drooping one. Tighten the small screw under the lever with a 3 mm hex key until the lever stops wobbling. Snug by hand is enough. If the lever now sits level and returns by itself, you're done.
Look for a rubbing shaft
Take the inside handle off and look where the shaft passes through the door. Shiny rub marks on the shaft, or fresh shavings in the hole, tell you something is dragging. Therma-Tru's installation guide for this lock lists it under "handle sags or returns slowly": wood or cladding in the hole rubs the shaft. Its fix is to file or drill the hole slightly larger so the shaft lines up.
Then the spindle check
This observation may help narrow down the cause. It does not prove which part has failed.
Unlock the door and open it, so nothing is loading the bolts.
Take the inside handle off. Loosen the set screw under the lever, then remove the screws in the inside plate.
Push the bare square spindle down gently with your fingers, and let go.
It stays down: the case may need attention. Confirm the cause and compatibility before ordering.
It springs back to level: inspect the handle and look for friction; this does not rule out every case fault.
HOPPE's own guides don't say where the return spring sits. Locksmiths who repair these locks report that the lock case carries its own, so treat this as a quick check, not a factory procedure.
What to check next
| What the checks showed | Next step | Where |
|---|---|---|
| The bare spindle stays down | Confirm whether the case has failed, then match the lock family and dimensions | Choose my size |
| The bare spindle springs back | Check the handle and spindle for looseness or interference before replacing anything | Handle sets on shootbolt.com |
| It was only loose | Nothing, or a 3 mm hex wrench if you don't own one | You can add the wrench with a lock case order |
| It locks open but not shut | Nothing yet. Adjust the strike plates or hinges | |
| The faceplate strip or a locking point is bent or broken | A bigger repair than the case alone | Lock case or whole lock? |
Before you order the lock case, check that your lock is a HOPPE HLS 9000 and take two measurements.
Still not sure? Send us a photo of the door's edge and tell us what the handle does. We reply by email within 1 business day.
The part
HOPPE HLS 9000 replacement lock case
- Genuine HOPPE part, in six sizes
- Choose your size for price and availability
- Free US shipping and 90-day free returns