Shootbolt home

hoppemultipointlockreplacement.comHOPPE repair help by Shootbolt

Which lock do you have?

The name on your door isn't the name on your lock.

Therma-Tru, Sierra Pacific, Kolbe and Simpson make doors. The lock inside is often made by HOPPE. These checks help identify the lock family before you measure for a replacement.

Five checks, door open

You need a flashlight and a tape measure. Photograph the whole strip in the door's edge before you start: it helps if you ask us anything later.

  1. Read the stamp

    Look at the metal strip in the door's edge, near the latch and the deadbolt. A HOPPE lock is stamped with the HOPPE name and logo. The strip carries the logo only, not a part number.

Close-up of a stainless steel lock faceplate with the HOPPE name and logo stamped on it, circled
The HOPPE stamp, circled. Shown on a faceplate out of the door; on yours, look near the latch.
  1. Find the key

    Key below the handle: that is the HLS 9000, the lock this part is made for.
    Key above the handle: that is HOPPE's older HLS 7, a different lock. This part does not fit it.

  2. Lock it and watch what you do

    You lift the handle, then turn the thumbturn or key: a manual lock. That's the one.
    The lock throws its points by itself as the door closes: an automatic lock. It takes a different part.

  3. Count where it locks

    It locks above or below the handle as well as at the latch: a multipoint lock. That's the one.
    A latch and a deadbolt only: a single-point lock. The two are not interchangeable. See the single-point lock on shootbolt.com.

  4. Measure one distance

    From the center of the handle hole to the center of the key cylinder hole should be 3-5/8" (92 mm). Every size of this lock case has that spacing.

A HOPPE lock case with an arrow from the center of the square handle hole to the center of the key cylinder hole, labeled PZ
Handle hole to cylinder hole, center to center: 3-5/8" (92 mm). The trade calls this spacing PZ. Shown on a lock case out of the door.

All five match?

These details point toward the manual HOPPE HLS 9000 family. Confirm the current-style mechanism and match the case dimensions before ordering. One more thing to look at: the strip in the door's edge should be stainless steel. An older-style lock without the stainless steel faceplate takes a different part.

The strip comes 5/8" (16 mm) or 3/4" (20 mm) wide. Either is fine: one case suits both, because your own faceplate goes back on.

Next: two measurements choose your size.

What the door brand tells you

The name on the door belongs to the door maker, not the lock maker. HOPPE locks turn up on doors from Therma-Tru, Sierra Pacific, Kolbe, Simpson, Peachtree and others.

So the door brand is a clue, not proof. The same door maker can fit locks from more than one lock maker: a Simpson door may be stamped HOPPE or FUHR. Go by the stamp.

More on each door brand, on shootbolt.com: Therma-Tru · Sierra Pacific · Kolbe · Peachtree · Simpson pivot doors

If a check didn't match

  • The stamp says something else, such as FUHR, Amesbury or Truth. Match the part to the brand on the stamp. This lock case won't fit.
  • There is no stamp. Don't guess from the door brand. Send us a photo and we work it out with you.
  • The key is above the handle, the lock is automatic, or it is a single-point lock. It takes a different part.
  • The spacing isn't 3-5/8" (92 mm). It is a different lock family, even if it looks alike.

For any of these, use the instant part identifier on shootbolt.com, or send us a photo of the door's edge with your measurements. We reply by email within 1 business day.

HOPPE HLS 9000 lock case with latch and deadbolt

The part

HOPPE HLS 9000 replacement lock case

  • Genuine HOPPE part, in six sizes
  • Choose your size for price and availability
  • Free US shipping and 90-day free returns
Choose my size You pay on shootbolt.com, our store.
HOPPE HLS 9000 gearboxFree US shipping · 90-day returnsView sizes
Choose size