Multipoint door locked shut
Multipoint lock stuck shut? Take the load off the bolts first.
Most jammed multipoint locks aren't broken. The bolts are pressed hard against the metal plates in the frame. Here is how to open the door without damaging it, and what to check after.
How do you open a stuck multipoint lock?
Press the door firmly in its closing direction and hold it there. While you hold it, turn the key or thumbturn all the way back, then push the handle down. Don't force anything, and if the key, thumbturn or handle spins or clicks, stop and call a locksmith.
Someone trapped and in danger? Call 911.
That means a child alone behind the door, someone ill or hurt, smoke, or anything near water or heat. For a plain lockout with nobody in danger, call a locksmith. Only work on your own door, or one you have permission to open.
Two steps, in this order
Take the load off the bolts
A shifted door or a squashed weatherstrip presses the bolts hard against their strike plates, and a loaded bolt won't slide, however hard you turn. So press the door in its closing direction, as if shutting it harder: in toward the frame on a door that opens inward, or pull it toward you on one that opens outward. That's from inside. From outside, do the reverse. Press with your body, near the lock.
Unlock in the right order
Keep holding the door. Turn the key or thumbturn back fully first, then push the handle down. HOPPE's label for its HLS 9000 lock gives that order. Pushing harder on the handle while the deadbolt is still out is how gear teeth break. On an HLS 9000, a quarter turn can be the key's full travel.
No luck? Press firmer, near the lock, and try again gently. If someone is inside and safe, talk them through the same steps: on most multipoint doors, the inside thumbturn, then the inside handle, will open it.
The press-the-door tip comes from locksmiths and owners on repair forums, not from a lock maker's manual. It needs no tools and can't hurt the lock.
If the door still won't open
The thumbturn keeps clicking, the key turns all the way around, or the handle goes slack.
The drive to the bolts has broken, and pushing won't help. On a multipoint lock it is usually the lock case (the gearbox), sometimes the arm on the back of the key cylinder.
Don't drill the lock. Opening it without wrecking the door is a locksmith job. Call a locksmith or a door installer who works on multipoint locks.
Drill, grind, pry the frame, kick the door, or oil the keyhole.
Prying splits the frame and loads every bolt harder. Oil collects grit.
Card tricks and hinge pins won't work either. With the hinge pins out, the lock edge is still bolted top, middle and bottom.
If a locksmith says the whole door has to go, get a second opinion from someone who works on multipoint locks. On HOPPE locks the lock case is replaced on its own, and the door can usually be saved.
Once it's open: find out why before you lock it again
Don't lock it again until you know why it jammed. A failing lock case may not open at all next time.
Run the door-open test. With the door open, press in the small spring plunger beside the latch, lift the handle and turn the thumbturn. Turn the thumbturn back and push the handle down before you close the door again.
| What the door-open test shows | What it means | Next |
|---|---|---|
| Everything is smooth with the door open. It jams only with the door shut | No part yet. The door has moved in its frame | Adjust the strike plates or hinges |
| The handle clicks or flops, or the deadbolt won't come out | A gear or spring inside the lock case has failed | Signs the lock case has failed |
| Stiff or crunchy even with the door open, from both the key and the thumbturn | The lock case is worn | Choose my size |
| Stiff from the key side only | The key cylinder, which comes out on its own | Keys and cylinders |
| The faceplate strip or a locking point is bent or broken | A bigger repair than the case alone | Lock case or whole lock? |
If the door is new, ask the door maker first: the lock may be under warranty. If the lock case is your repair, check that your lock is a manual HOPPE HLS 9000, then take two measurements to pick your size. Review the swap procedure and required tools before starting. Not sure? Use the instant part identifier, or send us a photo of the door's edge and tell us what the lock does. We reply by email within 1 business day.
Questions about a jammed multipoint lock
How do I open a stuck multipoint lock?
Press the door in its closing direction and hold it, so the bolts aren't loaded against the frame. Then turn the key or thumbturn back fully, and only then push the handle down. Don't force the key or the handle. If anything spins or clicks, stop and call a locksmith.
How do you open a door with a broken multipoint lock?
If the thumbturn clicks, the key turns all the way around or the handle goes slack, the lock's drive has broken and no amount of pushing will open it. Don't drill it. Call a locksmith or door installer who works on multipoint locks. If anyone is locked in or in danger, call 911.
My multipoint door lock is jammed. How can I fix it?
First get the door open with the steps above. Then run the door-open test. If the lock works smoothly with the door open, the door is out of line: adjust the strike plates or hinges. If it is stiff, clicks or flops with the door open, the lock case is worn, and the lock case is the part to replace.
Does a stuck multipoint lock mean a new door?
Rarely. On HOPPE locks the lock case behind the handle comes out and is replaced on its own, and the strikes and key cylinder are separate parts too. A locksmith may still need to open a door that's broken shut.
Can WD-40 fix a stuck lock?
Not for long. Oil in the keyhole collects grit. If the keyway needs it, use dry graphite. See how to look after the lock.
The part
HOPPE HLS 9000 replacement lock case
- Genuine HOPPE part, in six sizes
- Choose your size for price and availability
- Free US shipping and 90-day free returns