Repair or replace a multipoint lock
How much to replace a multipoint lock? Often just one part.
It depends on what failed. Some faults need no parts, a worn handle mechanism is one part, and a whole lock is the biggest job.
The short answer
Replacing a multipoint lock often costs less than it looks, because HOPPE sells this lock part by part and you rarely need the whole lock. If the lock works with the door open but binds when closed, alignment or interference may be the cause. A DIY adjustment may need no replacement parts; professional labor is a separate cost. If the handle droops or won't spring back, the usual part is the lock case alone.
| What has failed | What you buy | What it costs |
|---|---|---|
| Works open, fails only with the door shut | Check alignment and interference before buying parts | A DIY adjustment may need no parts; professional labor varies |
| The handle droops, clicks or won't spring back | The lock case only | See today's price. Free US shipping |
| The faceplate strip or lower locking point is damaged too | A gearbox with its lower extension | Priced on shootbolt.com |
| The top is damaged as well, or no gearbox matches | The whole lock | The biggest part and the biggest job |
| The key is stiff, lost or broken | The key cylinder only | One part; the lock stays in the door |
Not sure which row is yours? Tell the handle problems apart.
Do I need to replace the whole multipoint lock?
Usually not. Locksmiths who repair these locks report that the lock case wears out and the upper half rarely breaks.
Test it with the door open: press in the small spring plunger beside the latch, lift the handle and turn the thumbturn. Turn the thumbturn back and push the handle down before you close the door.
If it all works open, the door is out of line: fix the door, not the lock. If the handle droops or the lock is stiff even open, the lock case is the usual part, and you keep the faceplate, extensions, handles, key cylinder and strikes.
Lock case or whole lock: the three sizes of repair.
If the door is new, ask the door maker before you buy anything: the lock may be under warranty.
Who repairs multipoint locks?
Some locksmiths and door installers do, but few say so. In our 2026 study of 9,443 U.S. locksmith websites, 283 (3.0%) said they work on multipoint locks. Ask first.
On a HOPPE HLS 9000, a locksmith's repair is a case swap too. HOPPE doesn't sell the springs and gears inside, so the case is replaced as one unit: the same part you can fit yourself.
We have no reliable figure for what a locksmith charges for this, so we don't quote one. Ask for a quote that names the part.
How to find a locksmith who works on these locks, and what to ask, on shootbolt.com.
Doing it yourself
For the case swap, have a #3 tri-wing bit and hand bit holder, a 3 mm hex key and a Phillips screwdriver ready. Allow time to compare the parts, refit them and test every locking point. See every step.
How do you replace or remove a whole multipoint lock?
A whole HOPPE HLS 9000 is the gear with its bottom extension, plus a top extension, plus a middle extension on tall doors. It comes out in one long piece. Keep the door open throughout.
Unlock and open the door
Turn the key or thumbturn back first, then push the handle down. Prop the door open.
Take out the key cylinder
Remove the long screw in the door's edge, level with the cylinder. Turn the key a little and slide the cylinder out.
Take off the handles
Loosen the set screw under each lever, remove the plate screws, and pull out the spindle.
Ease the lock out
Remove the screws along the faceplate strip and slide the lock out. If it won't slide out, don't force it: forcing bends the strip. Once those screws are out, take it all the way out; with the handles off it may fall out of the panel.
Compare old and new
Lay them side by side, handle holes lined up. The same lock fits the old groove and the strikes usually stay. If a locking point lands somewhere new, the frame needs a new strike cut in.
Refit and test with the door open
Put in a few screws and test every locking point. Then fit the rest hand-tight, refit the handles and cylinder, and test again before you close the door.
The lock case swap uses the same first steps: how to replace the lock case.
How to replace a French door lock
Start with the second door. The main door locks into it, so a loose second door makes the whole pair loose.
- Bolt the second door at the top and bottom, then push on it. If it moves, a bolt isn't in its hole.
- Test the main door's lock with the door open. Easy open and hard shut means a strike or the door is out of line.
- Stiff, crunchy or slack even open means the lock is worn. HOPPE sells the gearbox section on its own. Fix the alignment too, or the new part wears the same way.
The second door has its own lock in its edge, often under the strip where the two doors meet (the astragal). That is a different part from the main door's lock case. Not sure which you have? Use the instant part identifier, or send us a photo. We reply by email within 1 business day.
Questions
How much does it cost to replace a multipoint lock?
It depends on which part failed. An alignment adjustment may need no replacement parts, but professional labor is a separate cost. A worn handle mechanism needs only the lock case: see today's price.
Who repairs multipoint locks?
Some locksmiths and door installers. Few say so, so ask before you book.
Can a locksmith fix a multipoint lock?
Yes, if they work on them. On a HOPPE HLS 9000, a worn case is replaced, not rebuilt: HOPPE doesn't sell the parts inside.
Do I need to replace the whole multipoint lock?
Rarely. Test it with the door open. A drooping or stiff handle usually needs the lock case alone. Check which repair you need.
How do you replace a multipoint lock?
Take the lock out (steps above), swap the part that failed, and test every locking point with the door open. Step by step.
How do you remove a multipoint lock from a door?
Door open and unlocked: cylinder out, handles and spindle off, faceplate screws out, then ease the lock out. Don't force it.
How do I replace a French door lock?
Bolt the second door first, then test the main door's lock with the door open. If it is worn even open, replace the gearbox section.
When should I call someone instead?
Call a locksmith or door installer if the door is locked shut, a new lock needs strikes moved, or nothing you measure matches. If anyone is locked in or in danger, call 911.
The part
HOPPE HLS 9000 replacement lock case
- Genuine HOPPE part, in six sizes
- Choose your size for price and availability
- Free US shipping and 90-day free returns